2014Iranian Journal of RadiologyOpen access

QCT and Diagnosis of Osteoporosis

Laleh Ebrahimpour

Open full text 0 citations

Abstract

: Noninvasive measurement of bone mineral density (BMD) is a technology that benefits both the patient and society through its potential to decrease the morbidity, mortality, and cost of fractures associated with osteoporosis through early detection and treatment. In general, two sites are assessed, the spine and the hip. If one of these sites cannot be assessed, the protocol should outline the next site to be used. Quantitative computed tomography (QCT) can identify patients with low BMD compared to the QCT reference database and who are at risk for fracture. QCT cannot be used to diagnose osteoporosis based on the quantitative BMD value obtained, since it has never been validated for WHO criteria. It is, however, the only other technology besides DXA that is approved for treatment follow up. Quantitative computed tomography (CT) is a three-dimensional non-projectional technique to quantify bone mineral density (BMD) in the spine, proximal femur, forearm, and tibia with a number of advantages to other densitometric techniques: cortical and trabecular bone can be separated, trabecular volumes of interest (VOI) are largely independent of degenerative changes in the spine; so, QCT can be used to assess/monitor patients with extensive degenerative disc disease, more sensitively than DXA for density changes in the vertebral body and 3D geometric parameters can be determined. Bone mineral density (BMD), as measured by QCT, is a true density measured in g/cm3, in contrast to dual-energy X-ray absorptiometry (DXA), which determines an areal density (BMDa) measured in g/cm2. It has also some disadvantages such as higher radiation dose and lack of applicability with WHO diagnostic criteria, Furthermore, diagnosis of low bone mass is made by using the QCT criteria which is technically more difficult than DXA unless spiral technique is used. In modern spiral CT scanners, various techniques are implemented to significantly reduce radiation exposure by optimally adapting the X-ray tube current to the individual subject being scanned. The level of dose reduction depends on anatomical location. However, due to limited medical evidence, definitive advice on its use in all clinical practices cannot be provided until more data emerge.

About this research paper

What this paper is about

: Noninvasive measurement of bone mineral density (BMD) is a technology that benefits both the patient and society through its potential to decrease the morbidity, mortality, and cost of fractures associated with osteoporosis through early detection and treatment. In general, two sites are assessed, the spine and the hip. If one of these sites cannot be assessed, the protocol should outline the next site to be used. Quantitative computed tomography (QCT) can identify patients with low BMD compared to the QCT reference database and who are at risk for fracture. QCT cannot be used to diagnose osteoporosis based on the quantitative BMD value obtained, since it has never been validated for WHO criteria. It is, however, the only other technology besides DXA that is approved for treatment follow up. Quantitative computed tomography (CT) is a three-dimensional non-projectional technique to quantify bone mineral density (BMD) in the spine, proximal femur, forearm, and tibia with a number of advantages to other densitometric techniques: cortical and trabecular bone can be separated, trabecular volumes of interest (VOI) are largely independent of degenerative changes in the spine; so, QCT can be used to assess/monitor patients with extensive degenerative disc disease, more sensitively than DXA for density changes in the vertebral body and 3D geometric parameters can be determined. Bone mineral density (BMD), as measured by QCT, is a true density measured in g/cm3, in contrast to dual-energy X-ray absorptiometry (DXA), which determines an areal density (BMDa) measured in g/cm2. It has also some disadvantages such as higher radiation dose and lack of applicability with WHO diagnostic criteria, Furthermore, diagnosis of low bone mass is made by using the QCT criteria which is technically more difficult than DXA unless spiral technique is used. In modern spiral CT scanners, various techniques are implemented to significantly reduce radiation exposure by optimally adapting the X-ray tube current to the individual subject being scanned. The level of dose reduction depends on anatomical location. However, due to limited medical evidence, definitive advice on its use in all clinical practices cannot be provided until more data emerge.

Why it matters

A significance statement is not available in the OpenAlex record.

Key contribution

A contribution statement is not available in the OpenAlex record.

Method / approach

Method details are not available in the OpenAlex metadata.

Main findings

Findings are not separately available in the OpenAlex metadata.

Limitations

Limitations are not available in the OpenAlex metadata.

Applications

Application details are not available in the OpenAlex metadata.

Available abstract

: Noninvasive measurement of bone mineral density (BMD) is a technology that benefits both the patient and society through its potential to decrease the morbidity, mortality, and cost of fractures associated with osteoporosis through early detection and treatment. In general, two sites are assessed, the spine and the hip. If one of these sites cannot be assessed, the protocol should outline the next site to be used. Quantitative computed tomography (QCT) can identify patients with low BMD compared to the QCT reference database and who are at risk for fracture. QCT cannot be used to diagnose osteoporosis based on the quantitative BMD value obtained, since it has never been validated for WHO criteria. It is, however, the only other technology besides DXA that is approved for treatment follow up. Quantitative computed tomography (CT) is a three-dimensional non-projectional technique to quantify bone mineral density (BMD) in the spine, proximal femur, forearm, and tibia with a number of advantages to other densitometric techniques: cortical and trabecular bone can be separated, trabecular volumes of interest (VOI) are largely independent of degenerative changes in the spine; so, QCT can be used to assess/monitor patients with extensive degenerative disc disease, more sensitively than DXA for density changes in the vertebral body and 3D geometric parameters can be determined. Bone mineral density (BMD), as measured by QCT, is a true density measured in g/cm3, in contrast to dual-energy X-ray absorptiometry (DXA), which determines an areal density (BMDa) measured in g/cm2. It has also some disadvantages such as higher radiation dose and lack of applicability with WHO diagnostic criteria, Furthermore, diagnosis of low bone mass is made by using the QCT criteria which is technically more difficult than DXA unless spiral technique is used. In modern spiral CT scanners, various techniques are implemented to significantly reduce radiation exposure by optimally adapting the X-ray tube current to the individual subject being scanned. The level of dose reduction depends on anatomical location. However, due to limited medical evidence, definitive advice on its use in all clinical practices cannot be provided until more data emerge.

Key concepts: Medicine, Quantitative computed tomography, Bone mineral, Osteoporosis, Densitometry, Bone density, Radiology, Femur

Related papers

Back to paper searchBrowse research topicsOriginal source
QCT and Diagnosis of Osteoporosis — Research Paper | ScholarLens